hans zimmer - davy jones free mp3 download

Name: hans zimmer - davy jones free mp3 download
Category: Soft
Published: gitfihightan1981
Language: English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Labels.
Session Time out- Maximum time the connection can stay up. By default no time limit is set.If you will setup any time the NAS will make log out to that user from NAS .
Lets Start the configuration .
I have given you the picture below of my network to run the PPPoE services .Here I am using this diagram .
PPPoE Profile.
Lets get in to the Profile 1.
Thursday, 1 June 2017.
This is very important to configure the PPPoE profile for PPPoE users because based on your profile the services will be available to the users .
NOTE:- The ip pooling is depend on your requirement because if you are using the radius server then you can enable the IP pooling in NAS and RAdius as welll but you cant enable the IP pooling in both nas and radius so you have to enable the IP pooling from one it can be your NAS or it can be your radius . But here I have enabled the IP pooling in NAS so I have disabled the IP pooling in Radius . If you want enable the ip pooling in NAs then you have to create one IP pool in NAS and Radius as well but the IP will be provided to the users by NAS .And you have to assign that Pool name in remote ip address .In my case I have configured the IP pool in nas the name of default and that IP pool i have configured in the Remote IP Address .
Local Address :- The Local Address means , this local address will be the gateway of your PPPoE users and for recommendation it would be your WAN IP but also you can give your LAN ip .
Here, I am using the radius server with Mikrotik NAS so I have to select the Use Radius .
You have to enter the DNS ip in the profile because it's very important to get the DNS for users otherwise they will not able to browse the internet .
Remote IP address:- The remote IP address means the users will get the IP address when they will dial using their username and password .
One session Per host:- Allow only one session per host (determined by MAC address). If a host tries to establish a new session, the old one will be closed.
MIKROTIK:-PPPoE Server Configuration with DMA Radius .
Idle Timeout:- Specifies the amount of time after which the link will be terminated if there are no activity present. Timeout is not set by default.
Here is some important things to have in the PPPoE profiles .
MAX MTU- Maximum Transmission Unit. The optimal value is the MTU of the interface the tunnel is working over reduced by 20 (so, for 1500-byte Ethernet link, set the MTU to 1480 to avoid fragmentation of packets.The recommenced MTU 1492 because there is adding some extra 8 bit ine header . so it's important to keep in your mind .

(Mikrotik,Cisco,ubiquiti,DMA Radius,Mikroitk NAS,Usermanager,Cent OS,Ubuntu,Redhat,Syslog,FTP,TFTP,Rsyslog,)
All ISP Networking Technologies.
As an engineer in ISP domain you have to know some of the important key points before implement the PPPoE network in your organisation .As per as My recommendation this blog will help you to know more about PPPoE services .Now a days there are all the radius company which is compatible to run the PPPoE services with Mikrotik .
Here , I have a default IP pool in Mikrotik pool list and the users will get the ip address from that IP pool , But i have not configured any IP in my PPPoE interface from That sub net (192.168.0.0/24).
In my case I have selected the Profile1 as profile of my PPPoE server .
Service Name: Which ever the service name you can give according to you but sometimes you can create a problem like that when the users are setting their dial up connection they have to enter this exact service name in their device . Interface :- which interface you want to run the PPPoE services you have select that same interface in the interface list .And all your PPPoE users will be connected from that interface only .
After creation the IP pool in NAS ,you have to assign that ip pool in Remote IP address list .and after that when the users will be dial using their username and password they will get the IP from this Pool of NAS .
NOTE:---Whichever the IP address you are providing to the users after verifying the username and password please Don't configure any IP address in PPPoE interface from that subnet . So it's not recommended to configure the ip address in PPPoE interface .Because the ip will be thrown by Mikrotik NAS from the IP pool which you have assigned in the remote ip pool list of PPPoE profiles.
http://ylrioledust1975.eklablog.com/knihy-pdb-download-a177968344