Our pro, Jerome Worm, has become utilizing a miter saw on a daily basis for 30 years. He describes how to find the most out of your respective miter saw and shared guidelines on how to cut small items, cut down tear-outs and, most significant, how to make it happen all safely and securely.

Cleanse, Safe and sound Miter Observed Cuts

Dropping the miter observed blade into your workpiece far too rapidly is risky and may possible cause a tough Lower or splintered Wooden. This can be especially true any time you’re cutting thin, narrow pieces. Provide the motor a couple of further milliseconds to achieve entire speed, then decreased the blade bit by bit as you chop.

Use a Sacrificial Fence

To prevent launching modest parts across the room, utilize a sacrificial fence. Make a two-piece fence for small material such as this cove molding (still left). Or merely utilize a scrap board to back up modest cutoffs (correct). Keep the noticed down at the conclusion of the Minimize and Enable the blade come to a whole cease.

Carry a Miter Noticed by the Base

Miter saws are weighty and awkward to hold. Some saws have handles close to the top so you're able to lug them similar to a suitcase, but get in to the pattern of carrying them by The bottom as an alternative. It’s less difficult in your back and received’t beat up the aspect within your leg. It’s also much easier to get via door openings devoid of banging up the trim.

Ship Miter Noticed Dust Down

Controlling dust made by a miter observed is notoriously challenging. The collection luggage do tiny, and Even when you hook up a vacuum, dust remains to be intending to fly. Our expert changed his bag using an ABS plumbing elbow that healthy snugly onto the dust chute. It doesn’t Manage all of the dust, but it really sends a fantastic part of it to the floor instead of around. Dust chutes fluctuate in sizing, so evaluate yours before heading on the hardware shop. The one surefire solution to wholly avoid dust indoors is to perform your cutting exterior.

Mark a Guideline on the Miter Saw Base

Right here’s a fast solution to Lower a bunch of pieces to the exact same duration: Placement the primary one after which mark the location of the top on the saw base with a pencil. Now you do have a guideline for the rest of your sections. This technique will not be as correct as being a stop block, but in some cases perfection is needless. The pencil mark effortlessly rubs off whenever you’re accomplished.

Normally Don Listening to Safety

For those who asked our pro why he never ever wore Listening to protection when he was more youthful, he would probably offer you a blank stare unless he’s wearing his Listening to aids. Miter saws are loud and will damage your ears Except if you shield them. Our Professional might be the main to tell you that hearing decline is not any joke!

Make Micro-Adjustments

In this article’s a tip when you should shave off merely a small little bit: Lower the blade even though it’s not spinning, and drive the fabric tight up versus the human body on the blade. Get yourself a firm grip on the material and lift the blade. Upcoming, fire up the saw and reduce the blade all over again. Because the enamel of your blade are slightly wider than the human body, you’ll find yourself shaving off just a hair.

Screw Guides Onto the Miter Noticed Base

Clamping down A brief guideline would make chopping crown molding quite a bit a lot easier, but sometimes the clamps are tough to set up due to the irregular condition of most miter noticed bases. Clamps also can get in just https://pbase.com/topics/vindonvgsw/fdirxcs707 how whenever you’re switching the angle of the Lower. Don’t be afraid to screw down a information ideal into The bottom of one's saw. A little hole is not really intending to have an impact on just how the noticed performs. Self-tapping screws work fantastic in bases fabricated from aluminum: Just make sure you situation the quit so it doesn’t interfere if you’re changing angles. Put in a couple screws on either side In case the guidebook will get cut in 50 percent, and save your guides so You may use the same screw holes upcoming time.

Never ever Cross Your Arms

Sorry, lefties, but most miter saws are suitable for ideal-handed customers, this means the observed is operated with the appropriate hand and the material held down Together with the remaining. But sometimes the fabric must be held down on the ideal facet from the blade. On Those people instances, it’s tempting to even now make use of your correct hand to function the noticed, but doing this will trigger your left hand to cross before The trail with the blade—that’s terrible. It can feel Bizarre, but in this situation, make use of your left hand to function the saw and your ideal to safe the fabric. Our specialist is familiar with carpenters who have disregarded this recommendation and also have the scars on their own arms to establish it.

Minimize Broad Boards With the most effective Aspect Down

Splinters and tear-outs take place exactly where the blade breaks throughout the wood. That’s the bottom facet when plunge-chopping narrow boards, so it’s very best to chop narrow boards with the “show” aspect facial area up. But any time you’re chopping broader substance over a sliding saw, you’ll pull the blade towards you, lessen the blade then press it forward as you cut. In that method, splintering will occur on the top of the board, so Minimize Together with the board encounter down.