Our expert, Jerome Worm, has actually been using a miter saw each day for 30 years. He clarifies how to get the most out of your respective miter observed and shared strategies on how to Slice small pieces, cut down tear-outs and, most significant, how to do it all properly.

Clean up, Safe and sound Miter Observed Cuts

Dropping the miter noticed blade in the workpiece also quickly is perilous and can probably result in a tough Slice or splintered Wooden. This can be very true any time you’re reducing skinny, narrow pieces. Give the motor some additional milliseconds to succeed in complete speed, then reduce the blade bit by bit as you cut.

Use a Sacrificial Fence

To avoid launching tiny items throughout the space, utilize a sacrificial fence. Make a two-piece fence for small substance like this cove molding (left). Or perhaps make use of a scrap board to back again up small cutoffs (right). Hold the saw down at the end of the Minimize and Permit the blade arrive at a complete end.

Have a Miter Observed by The bottom

Miter saws are weighty and awkward to carry. Some saws have handles near the top so that you can lug them like a suitcase, but get into your behavior of carrying them by the base as a substitute. It’s easier on the back and received’t defeat up the side within your leg. It’s also much easier to get via doorway openings devoid of banging up the trim.

Send Miter Saw Dust Down

Controlling dust made by a miter noticed is notoriously hard. The collection bags do very little, and Even though you john witherspoon Miter saw deals hook up a vacuum, dust continues to be planning to fly. Our qualified replaced his bag using an ABS plumbing elbow that in good shape snugly onto the dust chute. It doesn’t Manage all of the dust, nonetheless it sends a fantastic percentage of it to the floor instead of all over. Dust chutes fluctuate in dimensions, so measure yours before heading on the hardware retail outlet. The only real surefire technique to totally avoid dust indoors is to carry out your reducing exterior.

Mark a Guideline over a Miter Observed Foundation

Below’s a fast technique to Minimize a bunch of pieces to the same length: Posture the initial a person after which you can mark the location of the tip to the observed foundation having a pencil. Now you have a guideline For the remainder of your components. This method will not be as precise like a stop block, but from time to time perfection is needless. The pencil mark easily rubs off if you’re performed.

Constantly Have on Listening to Security

In the event you requested our Professional why he never wore Listening to safety when he was young, he would in all probability provide you with a blank stare Except he’s wearing his Listening to aids. Miter saws are loud and may harm your ears unless you secure them. Our pro can be the main to inform you that Listening mitre saw Deals available to reduction is no joke!

Make Micro-Adjustments

Right here’s a tip when you must shave off just a small little bit: Reduce the blade while it’s not spinning, and push the fabric restricted up in opposition to the human body of the blade. Obtain a agency grip on the material and raise the blade. Future, fan the flames of the noticed and reduce the blade all over again. Because the enamel with the blade are marginally broader than the body, you’ll end up shaving off only a hair.

Screw Guides On to the Miter Saw Base

Clamping down A short lived information would make slicing crown molding a whole lot a lot easier, but at times the clamps are difficult to set up due to the irregular form of most miter noticed bases. Clamps may get in the way in which whenever you’re altering the angle of a Lower. Don’t be scared to screw down a manual suitable into The bottom of one's noticed. A small gap just isn't john witherspoon Miter saw likely to have an affect on the way the saw performs. Self-tapping screws work fantastic in bases fabricated from aluminum: Just make sure you situation the halt so it doesn’t interfere any time you’re switching angles. Install a few screws on both sides If your information can get Reduce in 50 %, and help you save your guides so You need to use the exact same screw holes upcoming time.

Hardly ever Cross Your Arms

Sorry, lefties, but most miter saws are suitable for ideal-handed end users, this means the saw is operated with the correct hand and the material held down While using the still left. But occasionally the material will have to be held down on the right aspect in the blade. On These events, it’s tempting to even now make use of your appropriate hand to function the noticed, but doing this will result in your left hand to cross before The trail of your blade—that’s terrible. It's going to sense weird, but in this case, use your left hand to operate the saw and your proper to secure the material. Our expert is aware carpenters who've dismissed this advice and also have the scars on their own arms to verify it.

Minimize Huge Boards With the Best Side Down

Splinters and tear-outs occur in which the blade breaks through the Wooden. That’s the bottom facet when plunge-slicing slim boards, so it’s greatest to cut narrow boards Together with the “show” side deal with up. But once you’re cutting wider material on a sliding saw, you’ll pull the blade toward you, decrease the blade and then thrust it forward as you cut. In that process, splintering will manifest on the top from the board, so Minimize Together with the board facial area down.