icq servers checker download

Name: icq servers checker download
Category: Download
Published: magiletu1975
Language: English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VX-1R Software and Hints.
VX-1R Controller Software.
Feature list: change basic configuration and contents of all memory groups modify the VX-1R, such as country setting, RX/TX coverage (provided the unit is hardware-wise prepared, i.e. only jumper #1 is set) free assignment of memories to bands (145.xxx can also be assigned to the U-HAM band) assign one particular memory to different bands at the same time (memory #1 appears in bands FM, V-HAM and ACT1) define all HOME memories freely and assign them to one or more bands define all 31 SMART SEARCH memories freely, including all options runs under DOS, has an attractive GUI and is mouse-controlled full cellular range is avialable for the Firmware to A106.
works both with the original ADMS Adapter and a simplified one published in cqDL magazine, Jan 2000 issue, p.27 . Use this Plug Here a selfmade LAYOUT and PCB Here a picture of a self made Plug only for cloning. This new ring was milling with a little millingmachine.
has been extensively tested with VX-1R A105 and A106 firmwares, but of course you do all reprogramming of your VX-1R at your own risk.
- Bug on entered QRG with 12.5 khz step are removed ! - Change the configuration with a mouse-click: COM1 or COM2 7 Color screens english or german version READ and SEND routine with ESC ( abort ) - synchr. the vx1 with the data-file ( country-code ) - copy memories from CG1 to CG2 and back - in the list of memory is also the shift, - power , mode and skip - Errors in alpha-Digit on QRG's with 12.5 khz step fixed - Error in COM2-routine is fixed - in SS-memory also DCS and CTCSS to change.
A Screenshot of the WIN-Software.
VX1R WinController Full-Version 2.1a Download 600 KB.
A Screenshot of the DOS-Software.
VX1R Controller Full-Version 1.92 Download 78 KB.
Which Firmware I have ?
PRESS and hold the AR-Key and do the radio power on.
Press the AR-Key step for step through the test-Mode ( 6. 7 steps) to in the display is the Firmware. Is in the display never a number, so is in the radio the version A106.
To end turn the radio off !!
Here a picture of the jumpers.
There are many instructions to widen the VX-1R's coverage.
Of course you can open it completely, so the VX-1R will always have full coverage. Don't think this is the preferred solution. With this software you can reconfigure your VX-1R any time without any hardware modifications, provided that only jumper 1 is set inside the unit. To do that, remove the battery, then remove 3 small screws. Now carefully open the case from the side where you removed the 3 screws. On the battery side there are 3 small plastic clips inside which will unlatch when you open the case. Remove the sticky foil from the PCB where the battery was before. Jumpers 0 and 1 are on the top, the others are further down. Make sure that only jumper 1 is set. Reassemble the unit, then do a RESET.
If your unit had the "Germany" configuration before, it will now be "Germany + wide TX":
Range TX RX Germany+TX+RX 140-170, 420-470 Mhz 76-999 Mhz FreeBand 108-560 Mhz 76-999 Mhz Germany 144-146, 430-440 Mhz depend of Wide RX Europe 144-146, 432-438 Mhz depend of Wide RX USA 144-148, 430-450 Mhz depend of Wide RX.
TX-Erweit. 140-170 Mhz 420-470 Mhz ( Germany,Europe,USA ) Cell RX 824-849/864-894Mhz RX WideRX .
With "FreeBand", the last 3 items become irrelevant, they are being shown as not selected. This is not a bug! Now, how do you modify your VX-1R using my software? It's very easy: Connect your VX-1R to your PC and read its contents. The right hand part of the screen, labelled "VX1R-Modify" is used to modify the VX-1R: Country setting, wide TX , wide RX, cellular RX. The top 4 buttons "VX-1R MODE" MUST always show the current settings. The lower 4 buttons "CHANGE TO" allow to select new settings. For instance click on the country button until it shows "FreeBand". Don't worry about wide TX and cell RX being shown as not selected, they don't matter in FreeBand. Now send the new configuration to your VX-1R, and it will be fully open. Change it back to its original configuration with the same procedure. To summarize: With jumper 1 set and all others open, you can reconfigure your VX-1R easily using this software.
SET the Squelch and S-Meter.
Lost data in VX-1 CPU for Squelch & S meter functions.
Reprogramming Procedure: Note: ** in procedure below repsents any number sequence.
- Press & hold the VOL + FW + TCall ( neath PTT ) buttons down together and power up the radio. - Now Display should show HSSQ03 (note: the important 3 is the small 3 at the top of the display. If anything but 3 appears at the top of the display, press the BAND button until the 3 appears) - Press the UP button to display HASQ** (Auto Squelch Hysteresis) - Turn the dial until the display shows HASQ08 - Press the UP button to display THSQ** (Squelch Preset Threshold) - Turn the dial until the display shows THSQ4F - Press the UP button to display TISQ** (Squelch Preset Tight) - Turn the dial until the display shows TISQ2F - Press the UP button 2 times to display S1LV** (S meter S1 level adjust) - Turn the dial until the display shows S1LV34 - Press the UP button to display S9LV** (S meter S9 level adjust) - Turn the dial until the display shows S9LVA3 - Press the UP button to display HSSQ03 (Squelch Hysteresis) - Press the BAND button 3 times until the display shows HSSQ06 (again note: this is the small 6 at the top of the display) - Press the UP button to display HASQ** - Turn the dial until the display shows HASQ08 - Press the UP button to display THSQ** - Turn the dial until the display shows THSQ4D - Press the UP button to display TISQ** - Turn the dial until the display shows TISQ30 - Press the UP button 2 times to display S1LV** - Turn the dial until the display shows S1LV27 - Press the UP button to display S9LV** - Turn the dial until the display shows S9LV96 - Press the FW button for 0.5 seconds to store these settings into memory. The radio will return to normal mode. - The reprogramming procedure is now complete.
The Cellular Frequency.
To scan the Cellular frequencies do the following steps.
USE MY SOFTWARE !! Read the VX1R-Data in the PC Change to Memory CG1 Enter in Memory L1 824.000 MHz and in U1 894.000 MHz Marked this Memories to the UHF-TV Band Switch the RX-Mode to Manualy and send this into the radio Take the radio in the UHF-TV Band with the Memory L1 Change to NFM and turn the DIAL to the VFO-Mode.
Now you can scan !!
See also the Unoffical YAESU VX-1R Page .

http://nexpsmetrozpcons.eklablog.com/qt-irreco-download-a178058644