If the decision of what type radiant heating system to use was left to the floor-coverings, it would choose electric radiant.  Eliminating the risk of water/glycol  leaks, standard floor-heights, simple retro-fits, almost unlimited choice of carpet  padding, uniform heat flux, easier installations and superior floor or space  temperature control are only a few of the advantages of electric radiant heat.  This  isn't to say that there aren't disadvantages of electric radiant, but then I'm a sparky  not a plumber, so I'm here to espouse the benefits and desirable features of electric  radiant heat and its loving relationship with any and all floor-coverings.  Oh, wait a  minute, how could I forget, electric systems cost a fraction what hot-water  (hydronic) systems do.

From the simplest of painted concrete to floors to floors that started with linoleum,  Multi Socket Outlet GL-25H-6 added carpet, then converted to imported marble, electric radiant is truly and simply  superior to hydronic radiant and here are the reasons why.

There is no water or glycol ? and spilled electrons don't damage floor-coverings, in  fact, there's no need to even sweep them up.  Seriously, the safety standards and  National Electrical Code keep electrical systems safe.  Yes, a cable, mesh or mat can  be damaged by an errant nail or screw, but the worst case scenario is the system  doesn't work as compared to a penetrated tube of a hydronic system with 100  gallons of water and glycol pumped out on the top level floor of a three floor  custom home.

Built-up floor height for most electric systems is less than ?? and some as little 1/ 16? thick.  Most hydronic systems pour 1 ?? of light-weight concrete over the tubes  increasing construction costs and limiting the types of floor-coverings that can be  installed.  If you want traditional hard-wood floors, a complex system of sleepers  must be installed to allow for nailing of the wood to the sub-floor.

Retro-fitting carpet over what used to be tile can't be easily done with hot-water  systems.  Changing the R-value (insulating characteristic) of the floor-covering  changes the amount of heat that makes it into the space in hydronic systems, since  they are designed to transfer heat via a temperature difference between the water in  the tube and the floor covering surface, whereas electric systems put out a constant  wattage regardless of the floor-covering insulating characteristics.  Floor covering  types can be changed time after time with electric radiant without changing the  heating system.

Hot and Cold Spots or what some-people call spot-heating can be easily  accomplished by installing higher or lower heat-density and adding a simple floor- sensor to control the temperature.  Have you ever noticed how dogs or cats search  for the warmest piece of flooring in a home and sleep there?  We added a special tile  floor heated 10? warmer for our house pet that became new sleeping  accommodations for Cairo.

Uniform Heat Flux ? The harder the floor covering the more noticeable warm or cold  spots become and the layout of the hot-water tubing and the changing temperature  of the water through the loop result in changing floor-temperatures.  This doesn't  happen with electric heat, each foot of cable, or length of mesh or mat generate  exactly the same amount of heat as the next foot making it very easy to maintain a  constant temperature across the floor.  If the floor-coverings are going to be  different in one room or one zone, split it into two zones of electric so the desired  temperature can be maintained on each surface.  This is easier to do and less costly  for electric than hydronic.

Installation of any product is a concern and any time the cross-trade issues of  installation can be minimized everyone wins.  Electric systems don't require any  mechanical room space so long as they are installed before the floor-covering is  installed you don't have to do a lot of coordination with the other trades.  If you  want to climatize some exotic hardwood flooring from Brazil within the space it's  unlikely that you'll have gas to operate your boiler, but it's very possible that you  can run your electric radiant heat off of temporary power to assist in stabilizing your  wood before installation.  Take that example one step further and you realize that  all the other trades on site will appreciate the temperature inside if it's Leadville,  Colorado in February.

Independent of HVAC ? Electric radiant can be the primary heating system, but can  operate very efficiently if you want the bathroom floor 80? in June and your husband  has the air-conditioner running throughout the rest of the house.  Try doing this  with your 1,000,000 Btu boiler and you'll regret it when the time comes to pay your  gas or oil bill.

Precise Temperature Control ? Adding multiple zones to an electric system costs  only pennies per foot compared to dollars per foot for hot-water.  Having as many  zones as you ever anticipate different areas with different floor-coverings is  possible and practical, with the other benefit of precise control of temperature of  every space in the home.

My mother and father used to sit and watch TV (football, basketball, etc.) in a love  seat in their master bedroom and my dad was always cold while my mom was  always hot.  I installed a two-zone electric system right underneath the love-seat  split right down the middle with a thermostat for my mom and one for my dad.   Believe it or not, it worked beautifully.  My dad's feet sat on a floor that was 85?  while my mom's were on a floor that was 75?.

Cost ? Installation costs of electric radiant is almost always less than any hot-water  installation and the smaller the area to heat the bigger the difference.  And here's  the kicker, if you save a lot of money on your radiant heating system you can spend  every penny of that savings on Imported Italian Marble in your Entry and Master  Bath. If you would like more information on radiant heat and it's benefits please visit us at  warmquest