Desk saws are ideally suited for ripping lumber—very long cuts parallel on the grain in the Wooden. However, just one widespread accent that is usually provided using your table noticed, known as a miter gauge, may make the desk saw just as beneficial for producing cross-cuts perpendicular for the grain with the wood at a variety of angles, from 90-diploma perpendicular cuts to miters of virtually any angle.

Due to the fact a desk saw's blade can even be established for angles around 45-levels, the miter gauge will allow your saw to make lots of the compound cuts which are Typically reserved for your compound miter observed or radial-arm noticed.

Most table saws feature miter gauges, but Additionally, there are specialised and extremely exact after-sector miter gauges You should buy. A very good miter gauge is often a highly exact piece of kit which could Value numerous hundred pounds.

Major-good quality Best Miter Saw Black Friday miter gauges are specific all the way down to fractions of the degree.

eight Tricks for Environment a Beautiful Desk

How a Miter Gauge Works

A miter gauge is made of a protracted slim metallic guidebook that rides during the miter slot inside the desk of the saw. Hooked up to this tutorial is really a fifty percent-moon formed head that pivots on its link position for miter saw black friday deals the information. A locking mechanism lets this pivoting part to generally be locked into any angle, from -45 levels to +45 levels). When a workpiece is placed in opposition to the fence of the gauge and the entire assembly (miter gauge and board) is slid forward across the observed blade, the workpiece is cut in the exact angle you named for.

Some miter gauges have "constructive stops" that allow the gauge being rapidly established with the most commonly utilised angles (like ninety-, 45-, 30-, and 22 1/2-levels).

Producing Square Cross-Cuts That has a Miter Gauge

As you learn how to use a desk noticed miter gauge, the best cut to learn is usually a sq. cross-cut, in which the miter gauge is about to 90 degrees based upon the angle markings over the gauge, and the top of the board is Lower square.

Even though the angle options on miter gauges are intended to be as exact as you possibly can, normally they can be one or more levels away from kilter. To examine the precision of one's gauge:

1. Established the gauge to 90 levels (or 0 levels, depending on how your gauge is marked) markings), for a sq. Minimize which is properly perpendicular to your miter slot on your desk saw).

2. Unplug your table noticed's electrical twine and lift the blade as substantial as it's going to go.

three. Slide the gauge ahead until it is in step with the entrance fringe of the exposed, stationary observed blade (don't endeavor this with out first disconnecting the saw from the ability source).

4. Put 1 sq. edge of a six-inch combination square against the observed blade, and the corresponding fringe of the square against the flat, forward fringe of the miter gauge. If your sq. aligns beautifully with equally the blade plus the gauge, then your gauge's configurations are correct.

If you will find any gaps amongst the square and both the blade or the gauge, regulate the angle of your gauge until eventually they align beautifully, and tighten the locking system.

To produce a cross-Lower:

1. Slide the miter gauge backwards (towards Your whole body) to the entrance fringe of the saw desk, and position a board versus the flat edge of the gauge.

2. Come up with a pencil mark over the wood in which you intend to make the cross-Reduce, and align that mark While using the noticed blade (even though trying to keep the board flat against the miter gauge).

3. Plug in and switch within the observed, then slide the miter gauge—Using the board held securely towards the head of the gauge—forward and earlier the observed blade, finishing the cross-Slash.

four. If the cut is completed, simplicity the board together the gauge and from the blade and slide The entire assembly back again towards the starting off place ahead of turning off the noticed motor.

As with all Procedure which has a desk observed, constantly keep the hands properly faraway from the desk noticed's blade.

Generating Angled Cross-Cuts That has a Miter Gauge

Angled cross-cuts are comparable to square cuts, except which the miter gauge is about to an angle of as many as forty five degrees right before sliding the gauge and corresponding Wooden piece towards the blade to make the Slice. When generating an angled Minimize utilizing the miter gauge, go the gauge a bit slower than you mitre saw Deals available probably did building a square Lower, given that the gauge's motion may have a tendency to slip the board from placement as you move it through the blade. A small woodworking clamp can be used to safe the board on the gauge as you make the Minimize.

Compound cuts, featuring both miter and bevel angles, might be concluded by placing both of those the angle of the miter gauge and also the bevel with the observed blade to the desired angles ahead of sliding the gauge ahead across the saw blade.

Adapting a Miter Gauge

When slicing extended boards (of as much as four ft in length), it's possible you'll wish to protected a sacrificial strip of wood to your experience of your miter gauge to offer added balance to the board currently being Reduce. Most miter gauges Possess a matching list of holes inside the back by which it is possible to travel a Wooden screw to secure the sacrificial board on the flat deal with with the miter gauge. Some significant-high quality miter gauges feature an extra-lengthy wood struggling with for just this purpose.

Furthermore, there are jigs that could be connected to the miter gauge to create specialty cuts. A person these kinds of case in point can be a box joint jig for creating perfectly-matched box joints (or finger joints) utilizing your desk noticed along with a stacked dado blade established.